|
Huntron's next generation
troubleshooting tool
with multi-pin scanning capabilities
The HuntronŽ TrackerŽ 2700S extends the capabilities of the popular Tracker
2700 to scan and compare up to 40 pins per channel using standard IC clips and
cables. Comparison can take place manually or automatically allowing you to pick
out the signatures differences quickly. Its low voltage ranges also make it
ideal for testing passive devices such as high value capacitors while still
in-circuit.
The Huntron Tracker 2700S is an ideal addition to the service engineer's
bench or as a compliment to a Huntron ProTrack I system. Using a power-off test
method known as Tracker Signature Analysis, it eliminates the risk of further
circuit damage, which often occurs when power is applied.
Troubleshooting Challenges
Modern complex switching power supplies with fail-safe protection circuits
contain many passive components that are difficult to test in circuit due to
parallel solid state devices. The 200mV range of the Tracker 2700S allows
resistors, capacitors and inductors to be analyzed without turning on the
parallel solid state devices. The passive devices are essentially tested "out of
circuit".
Today's portable electronic devices use 3 volt or lower logic circuits. The
low test voltage ranges of the Tracker 2700S make it an ideal tool to
troubleshoot these products.
The Tracker 2700S features variable ranges parameters resulting in over 100
combinations of voltage, source resistance and test frequency.
Tracker Signature Analysis
The Tracker works by applying a current-limited AC signal across two points
of a component. The current flow causes a vertical deflection of the CRT trace,
while the applied voltage causes a horizontal deflection. Together they form a
unique V/I signature that represents the overall health of the device under
test. Analyzing the signature can quickly determine whether the component is
good, bad, or marginal.
Specifications
| Sine wave |
| 20Hz, 50Hz, 60Hz, 200Hz and 2kHz |
| 200mV, 3V, 5V, 10V, 15V, 20V |
| 10Ω, 100Ω,
1kΩ, 10kΩ and 100kΩ |
| Manual or Auto Scan |
| 2 (A, B, Alternate), 40 pins/channel, automatic or
manual scan modes |
| 0.5 Hz to 5 Hz (synchronized to sinewave
zero-crossing) |
0 to 5VDC +DC output 25Ω 200mA maximum |
| 115VAC/230VAC |
| 50/60 Hz |
| 40 Watts maximum |
| 0.25 Amp type AGC fuse (operator replaceable) |
| color; 320x240 pixels |
| 11.5in W x 10.8in W x 4.5in H (29cm W x 27.4cm D x
11.4cm H) |
| 6.0 lb (2.8 kg) |
| +32°F to +104°F (0°C to +40°C) |
| -4°F to +140°F (-20°C to +60°C) |
| ETL listed |
| 1 year, limited |
Specifications are subject to change without notice.
Supplied Accessories:
The Huntron Tracker 2700S comes complete with:
| 1 pair |
Huntron MP20 Microprobes |
| 2 |
Common test lead |
| 2 |
20pin DIP clip cable |
| 2 |
40pin DIP clip cable |
| 2 |
20pin DIP clip |
| 2 |
40pin DIP clip |
| 1 |
Blue clip lead |
| 1 |
Power cord |
| 1 |
User's Manual (on CDROM) |
All specifications subject to change without
notice. Š1997 Huntron, Inc. All Rights Reserved. Huntron, Tracker, ProTrack and Personal
Troubleshooting Workstation are registered trademarks of Huntron, Inc. |