Fluke Current Clamp Accessories

Contact EMSCO today to purchase your Fluke Digital Multimeter
and take advantage of the Lifetime Limited Warranty on selected models

Fluke Product Home

Fluke Current Clamp Accessories
for Oscilloscopes and Power Meters

Current Clamp Resale Pricing

Precision Designed for Measurement with Oscilloscopes and Power Meters

These clamps will boost the performance of any oscilloscope or voltage input device capable of millivolt measurements. When connected to an oscilloscope or other waveform recording tool, they accurately reproduce current waveforms as they occur. Clearly see distorted waveforms that result from non-linear loads. Other current clamps, not designed for oscilloscopes, may add their own distortion over and above the actual distortion present in your power distribution system.

80i-110s AC/DC Current Clamp

The 80I-110s is compatible with any Fluke ScopeMeter Test Tool, Power Harmonics Analyzer, Oscilloscope, Multimeter, or other voltage measurement device that has the following features: BNC input connectors or if using a meter convert the banana plugs to a BNC connector using the adapter PM9081/001.

Current Range: 0.1 to 100A DC or 0.1 to 70A AC
Basic Accuracy (DC to 1kHz):
100mV/A setting: 50mA to 10A +/- 3% of reading + 50mA
10mV/A setting: 50mA to 40A +/- 4% of reading + 50mA
40A to 80A +/- 12% of reading + 50mA
80 to 100A +/- 15% of reading
Output Signal: 10A range: 100mV/A | 100A range: 10mV/A
Bandwidth: 1Hz to 20kHz
Working Voltage: 600V AC rms
Maximum Conductor Size: 11.8 mm (.46 inch) diameter
Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II, Working Voltage 600V

80i600A AC Current Clamp

The model 80i-600A is a clamp-on ac current probe designed to extend the current measuring capability of an ac current meter to 600 amperes. The clamp is compatible with a DMM that accepts 4mm-shrouded banana plugs and has an AC milliamp range. The division ratio is 1000:1.

Current Range: 1A to 600A AC (2000A Peak)
Basic Accuracy: +/- 2% of reading
Output Signal: 1mA / A
Frequency Range: 30Hz to 10kHz
Working Voltage: 750V AC rms
Maximum Conductor Size: 50.8mm (2.0 inch) diameter
Safety Rating: Protection Class II as defined in IEC 348 and ANSI C39.5

I-1000s AC Current Probe

Large AC Current Probe
The Fluke i1000s is a clamp-on ac current probe designed to expand oscilloscope applications in industrial and power environments. The Current Probe (shown in figure) provides the following features: Ideal for measuring distorted current waveforms and harmonics.

Allows accurate measurement of currents from 100 mA to 1000 A rms, 5 Hz to 100 kHz without breaking into the circuit
A passive filter eliminates noise and ring on rapidly rising di/dt waveform, ensuring accurate screen displays
Connects directly to an oscilloscope through a reinforced coaxial cable and an insulated BNC connector
Can be used with Multimeters with optional PM9081/001 BNC/Banana adapter
One year warranty

i1010 AC/DC Large Current Clamp

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools.

Battery-powered Hall-effect clamp-on probe measures ac current to 600A, dc current to 1000A
The i1010 is a single range ac/dc current clamp with mV output
The i1010 is compatible with most Fluke multimeters or any other current measurement device that accepts safety shrouded banana plugs
One year warranty

i1010-Kit AC/DC Current Clamp
and Carry Case

Special value kit for electrical professional who is looking to add on DC and AC current measurement capabilities to their DMM. Includes a roomy carry case to hold and protect your meter and current clamp, plus extra storage for your test leads, probes and manuals.

Included with kit:

i1010 1-600A AC rms, 1-1000A DC Current Clamp
Zippered vinyl carry case with moveable divider

i200s AC Current Clamp

Small sized, convenient-to-use AC current clamp
Fluke Current clamps are the ideal tools to extend the current ranges of Multimeters.
The i200 is a single range 200A ac current clamp with current output via safety shrouded banana plugs. The i200 is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs.

i2000PQ4 Current Clamp, 4-pack

A pack of 4 pieces of the i2000 current clamp, to be used for high current measurements. The Flex clamp fits around bus bars and large or hard-to-reach conductors. This 4-pack is perfect for use with 3-phase tools such as the Fluke 433 or Fluke 434.

i3000s AC Current Clamp

Very High AC Current Clamp
Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools.
The i3000s is a clamp-on AC Current Clamp for use with oscilloscopes and multimeters with banana input using the supplied Dual Banana to BNC Adapter. The clamp is optimized for measurement on power distribution systems.

i400 Current Clamp

Fluke Current clamps are the ideal tools to extend the functionality of Fluke tools. The i400 is a single range 400 A ac current clamp with current output via safety shrouded banana plugs. The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts 4mm-shrouded banana plugs and has an AC milliamp range. The division ratio is 1000:1.

Fluke i400s Current Clamp for Oscilloscopes

i400s AC current clamp for oscilloscopes and power quality analyzers

Pair a current clamp with your scope or power quality meter to measure up to 400 A AC
Only current clamp available with a CAT IV 600 V / CAT II 1000 V safety rating makes them ideal companions for modern CAT IV rated meters.
Specially designed to offer maximum utility in a compact shape
Take accurate current readings without breaking the circuit
Soft non-slippery overmold handle
Can be used with DMMs with optional PM9081/001 BNC/Banana adapter

i410 AC/DC Current Clamp

Large AC/DC Current clamp
Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools.

Battery-powered Hall-effect clamp-on probe measures AC/DC current from 1A to 400A
The i410 is a single range ac/dc current clamp with mV output
The i410 is compatible with most Fluke multimeters or any other current measurement device that accepts safety shrouded banana plugs
One year warranty

i410-Kit AC/DC Current Clamp and Carry Case Kit

i410 1-400A AC rms, 1-400A DC Current Clamp
Zippered vinyl carry case with moveable divider

Compatibility with multimeters

To connect these current clamps' BNC connectors with a multimeter's banana jack inputs, use a PM 9081/001 adapter (Female BNC to dual banana plug.)

Troubleshoot a Wide Range of Applications

With built-in safety features, including a 600V rms rating at the input jaws, output cable and BNC connector, these probes are ideal for troubleshooting industrial and commercial power distribution system components, including:

Distribution Transformers (causes of overheating and audible noise, due to harmonics or unbalanced phase loads)

Adjustable Speed Motor Drives (view waveforms for input current, output current, SCR or diode failure)

Electrical Panels (breaker tripping, view load effect as it switches between circuits)

Computers and Data Processing Equipment

Electronic Ballasts for Fluorescent Lighting

Safety Designed for Industrial Use

The 80i-500s and I-1000s are rated for 600V ac circuits of Overvoltage Category III (Heavy Industrial Rating) per IEC 1010-1 and EN61010-1:1993. It is also listed to UL 1244 for Protection Class II, double or reinforced insulation requirements.

The 80i-110s is rated for 600V circuits of Overvoltage Category II and 300V circuits of Overvoltage Category III, per IEC-1010-1. In addition, it meets the double or reinforced requirements of UL 1244 and CSA C22.2 No. 1010-1 Category II, Industrial Rating.