Technical Data

True-rms current (ac + dc)
Ranges: 50.00 A, 500.0 A, 5.000 kA, 50.00 kA,
1250 KA
Accuracy: ±(1% +10 counts)

Frequency
Ranges: 10.0 Hz to 15.0 KHz
Accuracy: ±(0.5% + 2 counts)

Crest Factor
Ranges: 1.0 to 10.0
Accuracy: ±(5% + 1 count)

PF Power Factor
Ranges: 0.00 to 1.00
Accuracy: ± 0.04

DPF Displacement Power Factor
Range: 0.00 to 0.25 Not specified,
0.25 to 0.90 ± 0.04, 0.90 to 1.00 ± 0.03

Hz frequency fundamental
Range: 40.0 to 70.0 Hz
Accuracy: ± (0.5% + 2 counts)

Phase: Volt & Amps (between Fund & Harmonic) Accuracy: 2nd (± 3º) . . . 51st (± 15º)
Watts (between Volt Fund. & Amps Harmonic)
Accuracy: Fund (± 15º)

K-Factor (Amps & Watts):
Range: 1.0 to 30.0
Accuracy: ± 10%

THD:
Range: 0.00 to 99.99
Accuracy ± (3% + 8 counts)

Vrms actual, Vrms max, min (AC+DC):
5.000 V, 50.00 V, 500.0 V, 1250 V*
Accuracy: Readings ±(2% + 10 counts), Cursor readings ± (2% + 12 counts), Cursor Readings Average ± (2% + 10 counts)

Arms actual, Arms max, min (AC+DC):
50.00 A, 500.0 A, 5.000 kA, 50.00 kA

Parameters: Choose up to two from one of the groups below:

V/A/Hz: Line voltage, current, frequency

Power: Watts, VA, VAR, PF, DPF, frequency

Harmonics: THD, volts(Fund. & Harmonics), Amps (F&H) Watts (F&H) Freq. (H),%(H) of total, Phase(H), KF

Ohms: Ohms, Diode, Continuity, Capacitance

Temperature: °C or °F

Scope: DC voltage, DC Current, AC Voltage, AC Current, Frequency, Pulse Width + or -, Phase, Duty cycle + or -, Peak max, Peak min, Peak min-max, Crest Factor

Useful bandwidth input 1: DC to 1 MHz (with test leads TL24)

Number of transients 40

Voltage threshold settings: 20%, 50%, 100%, 200% above or below reference signal

Reference signal: After START, the Vrms and frequency of the signal are measured. From these data a pure sinewave is calculated as reference for threshold setting.

Vpeak min, Vpeak max at cursor:
10 V, 25 V, 50 V, 125 V, 250 V, 500 V, 1250 V
Accuracy: ±5% of full scale

Inrush times (selectable):
1 s, 5 s, 10 s, 50 s, 100 s, 5 min

Cursor readings
A Peak max at cursor 1 and cursor 2
Accuracy: ± 5% of full scale

Time between cursors
4 to 235 pixels (1 pixel = inrush time/250)
Accuracy: ±(0.2% + 2 pixels)

Input 1:
Ranges: 1 MΩ//12 pF; with BB 120: 20pF
Accuracy: ±2 pF; with BB120 ±3 pF

Input 2:
Ranges: 1 MΩ//10 pF; with BB 120: 18pF
Accuracy: ±2 pF; with BB120 ±3 pF

Vertical

Voltage Ranges:
Ranges: 50 mV/div to 500 V/div
Accuracy: ± (1% + 2 pixels)

Vertical sensitivity, resolution:
Ranges: 5 mV/div to 500 V/div, 8 bit (256 levels)

Bandwidth input 1 (voltage):
Ranges: DC to 20 MHz at inputs, or with BB120 and VPS 100-R probe (opt); 1 MHz with TL24 Leads

Bandwidth input 2 (current):
DC to 15 kHz at inputs
10 kHz with 80i-500s Current Clamp

Coupling:
DC, AC (10 Hz -3 dB)

Horizontal

TimeBase modes:
Normal, roll, single

TimeBase ranges:
Ranges: 60 s/div to 20 ns/div
Accuracy: ± (0.4% + 1 pixel)

Sampling rate: 25 MS/s

Record length (min/max samples):
512 per channel

Trigger source:
Ranges: Input 1 or Input 2 or Automatic selection

Trigger Mode:
Automatic Connect-and ViewTM, Free Run, Single Shot.

Connect-and-ViewTM:
Advanced automatic triggering that recognizes signal patterns and automaticaly adjusts triggering, timebase and amplitude. Automatically displays stable pictures of complex and dynamic signals like motor drive and control signals.

Pre Trigger:
Up to 10 divisions

Measurement readings, per channel selectable:
Ranges: Volts & Amps (DC, AC, AC + DCrms, Peak max, Peak min, Peak min/max). Frequency, Duty cycle + or =, Phase, Pulse Width + or -, Crest factor

Diode voltage:
Ranges: 0 to 3.000 V
Accuracy: ±(2% + 5 counts)

Continuity, shorts > 1 ms:
Ranges: Beeper on at < (30 Ω ± 5 Ω)
Accuracy: Not Applicable

Capacitance:
Ranges: 50.00 nF, 500.0 nF, 5.000 µF, 50.00 µF,
500.0 µF
Accuracy: ±(2% + 10 counts)

Temperature:**
Ranges: -100.0 ºC to 400.0 ºC, (-200.0 ºF to 800.0 ºF)
Accuracy: ±(0.5% + 5 counts)

Max current, max open circuit volt:
Ranges: 0.5 mA, < 4 V (all functions above)

General Specifications