Oscilloscope Mode

• Fluke 199= 200 MHz
• Fluke 196= 100 MHz
• Fluke 192= 60 MHz

Rise time:

• Fluke 199= 1.7 ns
• Fluke 196= .5 ns
• Fluke 192= 5.8 ns

Bandwidth limiter: User selectable 10 kHz or 20 MHz

Number of inputs: 2 plus external trigger. All isolated from each other and ground.

Input coupling: AC, DC with ground level indicator

Input sensitivity: 5 mV/div to100 V/div

Input voltage: See general specifications for maximum rating

Vertical resolution: 8 bit

Accuracy: ±(1.5% of reading + 0.04 x range/div)

Input impedance: 1 MW ± 1% // 15 pF ± 2 pF

• Fluke 199= 2.5GS/s
• Fluke 196=1 GS/s
• Fluke 192=500 MS/s

Number of digitizers: 2

Time base range:

• Fluke 199 and 196= 5 ns/div to 5 s/div
• Fluke 192= 10 ns/div to 5 s/div

Maximum record length: 1,000 points per input
27,500 points per input in ScopeRecord™-roll mode
(10 ms/div ... 2 min/div)
Accuracy: ± (0.01% of reading + 1 pixel)
Glitch capture: 50 nsec (5 µsec/div to 1 min/div) Faster time bases have higher sample rates than
20 MS/s

Modes: Automatic Connect-and-View™, free run, single shot, edge, delay, video, video line, selectable pulse width

Connect-and-View™: Advanced automatic triggering that recognizes signal patterns, automatically sets up and continuously adjusts triggering, time base and amplitude. Automatically displays stable waveforms of complex and dynamic signals like motor drive and control signals.

Video triggering: NTSC, PAL, PAL+, SECAM. Includes field 1 and 2 and line select.

Pulse width triggering: Pulse width qualified by time. Allows for triggering t, = t, ¹ t, where t is selectable in minimal steps of 0.01 div or 50 nsec.

Time delay: 9 divisions pre-trigger view to 1,000 divisions trigger delay

Replay: Manual or continuous replay. Displays the captured 100 screens as a “live” animation. The contents can also be viewed by manually scrolling backwards and forwards “screen by screen”.

Replay storage: Up to 2 sets of 100 screens can be saved for later recall and analysis.

Dual horizontal lines: Voltage at cursor 1 and 2, voltage between cursors

Dual vertical lines: Time between cursors, voltage between markers

Single vertical line: Min-Max and Average voltage at cursor position

Meter Mode

VAC true rms
15 Hz to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
VAC+DC true rms
DC to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)

Accuracy: ± (0.6 % + 5 counts)

Diode test: Up to 2.8V

Amps: Amp DC, Amp AC, Amp AC+DC using an
optional current clamp or shunt. Scaling factors:
0.1 mV/Amp to 100 V/Amp

Temperature (°C, °F): With optional accessories.
Scale factors 1 mV/°C or 1 mV/°F

Input impedance: 1 MΩ ± 1% // 10 pF ± 2 pF

Advanced meter functions: Auto/manual ranging, relative measurements (Zero reference), TrendPlot recording

Recorder Mode

Source and display: Input A, Input B, Dual

Memory depth: 27,500 points per input. Each point consist of Min-Max pair.

Min-Max values: Min-Max values are measured at high sample rate ensuring capture and display of glitches

Sample Recording Settings:
Set Time base range = 10 ms/div to 1 min/div:

• Recorded timespan: 11 sec to 15 hrs
• Glitch capture: 50 nsec
• Sample rate: 20 MS/s
• Resolution: 400 µsec to 2 sec
  

Set Time base range = 2 min/div:

• Recorded timespan: 30 hrs
• Glitch capture: 250 nsec
• Sample rate: 4 MS/s
• Resolution: 4 sec

Recording modes: Single sweep, continuous roll, start on external trigger

Horizontal scale: Time from start, time of day

Zoom: Up to 100 x zoom

Memory: Up to 2 dual input ScopeRecordings can be saved for later recall and analysis

Source and display: Input A, Input B and DMM input

Memory depth: 13,500 points record per input. Per record point a minimum, maximum and average value, and a time and date stamp are stored.

Ranges: 10 s/div to 20 min/div in normal view mode. 10 min/div to 24 hour/div in view-all mode (overview of total record)

Recorded timespan: Up to 8 days with a resolution of 1 minute

Recording mode: Continuous roll

Measurement speed: 2.5 measurements per second maximum

Horizontal scale: Time from start, time of day

Zoom: Up to 64x zoom

Memory: Up to 2 TrendPlot recordings can be saved for later recall and analysis

Dual vertical lines: Min-Max or Average voltage. Time between cursors.

Single vertical line: Min-Max or Average voltage. Absolute date and time or time from start.

General Specifications

Drip and dust proof: IP51 according to IEC529

Shock and vibration: Shock 30g, Vibration 3g
according to MIL-T28800E, Type III, Class 3, Style B

Size: 105 x 79 mm (4.1 x 3.1 inches)

Resolution: 240 x 240 pixels

Contrast and brightness: User adjustable,
temperature compensated

Recorder memories: 2 memory locations that each can contain 100 captured dual input scope screens, or a dual input ScopeRecord (27,500 Min-Max pairs per input), or a dual input Trendplot (13,500 Min-Max pairs per input).

Battery power: Rechargeable NiMH (installed)

Battery operating time: 4 hours

Battery charging time: 4 hours

Battery power saving functions: Auto power down with adjustable power down time. On screen battery power indicator

Weight: 1.95 kg (4.3 lbs)

Floating voltage: 1,000V CAT II, 600V CAT III
(Maximum voltage between earth ground and any terminal (signal input or shielding))

Independently isolated: 1,000V CAT II, 600V CAT III
inputs (Maximum voltage between any terminal of
one input or probe (VP190) and any other terminal
of another input or probe (VP190))

Maximum voltage on BNC input directly
(input A or B): 300V CAT III

Maximum voltage on meter input: 1,000V CAT II, 600V CAT III

Storage temperature: -20 °C to +60 °C

Humidity
10 °C to 30 °C: 95% RH non condensing
30 °C to 40 °C: 75% RH non condensing
40 °C to 50 °C: 45% RH non condensing

Maximum operating altitude: 3,000 m (10,000 feet)

Maximum storage altitude: 12 km (40,000 feet)

Electro-Magnetic Compatibility: EN 61326-1 for emission and immunity

To PC: Transfer instrument settings, screen images and waveform data, compatible with FlukeView®software for Windows® via optional PM9080.